1.2.7. System Setup

1.2.7. System Setup
1

Connected modules

1. Connected modules
Opens the menu Connected modules with menu entry
a) System
b) Data-Export
2

Menu System

2. Menu System
Opens the submenu System
3

InkZonePerfect

3. InkZonePerfect
When InkZonePerfect (ink-preset) is installed on the same computer then enable it here.
After the activation, a new job from always starts from InkZonePerfect by selecting the prepared CIP3 data with job name and color separation.
 
 
Note
The current job path is correctly pre-selected. Change the path only when required.
Job setup in InkZonePerfect, see here:  1.2.3.2.1. Calibration Curve InkzonePerfect
4

InkZoneLoop

4. InkZoneLoop
Setting Enable/Disable
With InkZoneLoop installed on the same computer, enable the application in IZMove here.
All measurement data created by InkZoneMove is sent to the selected scan data folder to be processed by InkZoneLoop.
 
Setting: Disable key for out of range density
Set a density threshold to detect wrong scan data. When the scan data values exceed the threshold will cause no regulation for this particular ink-key.
 
Sample:
Target density setup = 1.55
Measurement = 0.3
Setup "disable key for out of range density " = 0.85
Difference of target / measurement = 1.55 - 0.3 = 1.25
The difference 1.25 exceeds the setup value 0.85. The ink key will be not regulated
 
An ink-key where the density is detected as "out of range" is shown with a red warning triangle and is not regulated at the press.
 
 
With InkZoneLoop installed, verify the synchronize option (needs to be activate) in the press setup.
 
5

InkZoneReport

5. InkZoneReport
Company name and logo
Select company name and logo which appears on the report print out
 
PDF job name setup
Setup a job name with the parameters in  brackets for generating the job name
for PDF sheet and production reports:
<job>
job name
<sheet_report>
if the term Sheet-Report appears in the name
<production_report>
if the term Production-Report appears in the name
<date><time>
date and time
<sheet_number>
sheet number

 E-Mail report setup
Sends PDF reports over e-mail.
Setup mail server SMTP host address and port. Define the e-mail sender's address.
See further information on sending mails through Google Mail: Send e-mail with Google Mail server

 
E-Mail recipients
Create an alias with one or a group of e-mail recipients. For a group of recipients, use a semi-colon to separate the mail addresses.
An alias is either internal or external. This helps avoiding mistakes when sending reports.
The rule is that e-mails defined as internal can be send always whereas external addresses are sent only when customer name from the job setup matches the e-mail alias name.
See setup customer name here:  1.3.2. New Job
 
 
6

InkZoneTVI

6. InkZoneTVI
Displays information about the current compensation data set for a given press and targetset which both are selected from the drop down list:
 
7

IZKomoriConnect

7. IZKomoriConnect
InkZoneKomoriConnect links to the Komori PDCS closedloop application
1
Komori CLC program
Set the path to the Komori CLC program. Usually it is located in folder C:\PDCS
2
CLC version
Select 3 or 4 (double check what is installed)
3
COM port
COM port used by the CLC program
4
Closedloop mode
Semi- and full auto. Standard is semi auto which requires the operator to confirm ink-key changes at the console desk. The setting Auto changes ink-keys immediately after transfer.
5
Wait for both sides...
Enable when using a perfecting press. Data is sent to press when both sides are scanned
 
When using an IZSwitchbox than configure the parameters here:
 
1
IP address
set IP address , usually 192.168.0.99
2
Relay channel
usually channel 1 is used
 
Use  job name information from Komori KMS:
1
Path
Select the path to the status folder within KMS
2
Project and job name
Form the IZMove job name by project and job name from KMS
 
8

Measurement Devices

8. Measurement Devices
The command path is used to communicate to InkZonePerfect / Loop and needs to be set in these programs to the same location.
 
The scan path for the measurement data delivered by the scan instrument drivers IntelliTrax, EasyTrax, Graphometronic or SpectroJet.
 
The colorbar path is populated by InkZoneMove with the colorbar information file CBF for the scan instrument driver
 
Note: the default directories are correctly set and therefore change only when required.
 
9

Archive

9.  Archive
The oldest jobs are automatically archived to the selected archive path when the condition free disk space is less then x % of the disk drive.
 
10

Central Database

10. Central Database
Use a centralized database for jobs and spot colors.
The local database automatically synchronizes to the main database and vice versa.
11

User Setup

11. User Setup
Enable the user management here. Add and modify existing user.
 
12

Touchscreen

12. Touchscreen
Enables features to run optimized for touch-screen controlled PC.